폐도료 합성수지의 특성과 재활용 (Characteristics of Wasted Paint Resin and Its Recycling)

서지정보

· 발행기관 : 한국폐기물자원순환학회
· 수록지 정보 : 한국폐기물자원순환학회지 / 25권 / 1호 / 58 ~ 65페이지
· 저자명 : 김준호, 김희주, 이성범, 최창규, 김문일

초록

Paint is widely used on industry with the object of target's surface protection and aesthetics. However, outdated paints are wasted due to the development of updated products for the new trend of colors and quality. Solvent which is one of the paint ingredients can be easily collected by the methods of heating or centrifuging, the recovered solvent is reutilized
as a cleaning solvent or low class fuel. On the contrary, it is much difficult to separate a paint resin, pigment and additives, and recycling is limited. This study is to compare heating recovery with centrifugal method for collecting solvent from the paint which wasted in a paint production company for an automobile. In the experiment of heating recovery, it showed
that solvent recovery rate was about 90%, however, it had a problem that a paint resin was hardened by heating. On a centrifugal method, solvent recovery rate was 80% and it presented less recovery efficiency than heating method, and there was a characteristic that solvent was collected in a short time. In the result of FT-IR (Fourier Transform Infrared Spectroscopy) analyzing of extracted resin after solvent recovery, we found that it coincided with the inherent peak of acrylic resin, hence, an adhesive was made by mixing a epoxy adhesive with a acrylic resin. The tension and T-peel strength of the adhesive contained 25% of acrylic resin were 182 kgf/cm² and 14.3 kgf/cm², respectively, it found that a bonding strength was more increased than that as there was no acrylic resin. As a result of a risk assessment in worksite,
due to the difficulty of entire recovery for a solvent, MEK (Methyl Ethyl Ketone) was 2.3 ppm, it showed much little concentration comparing with 200 ppm which is exposure standard of hazardous substances in working.

영어초록

Paint is widely used on industry with the object of target's surface protection and aesthetics. However, outdated paints are wasted due to the development of updated products for the new trend of colors and quality. Solvent which is one of the paint ingredients can be easily collected by the methods of heating or centrifuging, the recovered solvent is reutilized
as a cleaning solvent or low class fuel. On the contrary, it is much difficult to separate a paint resin, pigment and additives, and recycling is limited. This study is to compare heating recovery with centrifugal method for collecting solvent from the paint which wasted in a paint production company for an automobile. In the experiment of heating recovery, it showed
that solvent recovery rate was about 90%, however, it had a problem that a paint resin was hardened by heating. On a centrifugal method, solvent recovery rate was 80% and it presented less recovery efficiency than heating method, and there was a characteristic that solvent was collected in a short time. In the result of FT-IR (Fourier Transform Infrared Spectroscopy) analyzing of extracted resin after solvent recovery, we found that it coincided with the inherent peak of acrylic resin, hence, an adhesive was made by mixing a epoxy adhesive with a acrylic resin. The tension and T-peel strength of the adhesive contained 25% of acrylic resin were 182 kgf/cm² and 14.3 kgf/cm², respectively, it found that a bonding strength was more increased than that as there was no acrylic resin. As a result of a risk assessment in worksite,
due to the difficulty of entire recovery for a solvent, MEK (Methyl Ethyl Ketone) was 2.3 ppm, it showed much little concentration comparing with 200 ppm which is exposure standard of hazardous substances in working.

참고자료

· 없음