3D 체표면 분할 전개방법에 의한 성인 남성 밀착원형 설계 (Development of tight-fit patterns for adult males according to the 3D body surface segment method)

서지정보

· 발행기관 : 복식문화학회
· 수록지 정보 : 복식문화연구 / 28권 / 1호 / 1 ~ 14페이지
· 저자명 : 홍은희

초록

This study is based on a representative body shape drawn from previous studies that classify adult male torso shapes. In this study, a design method is proposed by developing a tight-fit pattern that can be easily developed into various items and designs using the body surface development figure. This is obtained by converting the 3D body shape of the model representing the representative body shape. The specific design method was conducted as follows. Actual measurement values were used for waist back length, waist-to-hip length, shoulder length. The scye depth was determined as C/4–1.7 cm, and the front and back Interscye was set at (1/2 × actual measurements)–0.2 cm. The front-back neck breadth was set to (1/5 × base neck circumference)–1.3 cm and (1/5 × base neck circumference) cm. The front-back neck depth was set to (1/5 × base neck circumference)–1.2 cm and 3.5 cm. Front chest circumference was C/4–1 (front-back difference)cm; (1/4 × back chest circumference) was C/4 + 1 (front-back difference) + 0.3 (dart amount) cm. Front waist circumference was W/4–0.2 (front-back difference) + 2.2 (dart amount) cm; back waist circumference was W/4 + 0.2 (front-back difference) + 2.5 (dartamount) cm; front hip circumference was H/4 + 0.2 (ease) + 0.2 (front-back difference) cm; and back hip circumference was H/4 + 0.2 (ease)–0.2 (front-back difference) cm; Front droop was 1.6 cm. The newly developed tight-fit pattern is expected to be of great use as a basis for garment construction.

영어초록

This study is based on a representative body shape drawn from previous studies that classify adult male torso shapes. In this study, a design method is proposed by developing a tight-fit pattern that can be easily developed into various items and designs using the body surface development figure. This is obtained by converting the 3D body shape of the model representing the representative body shape. The specific design method was conducted as follows. Actual measurement values were used for waist back length, waist-to-hip length, shoulder length. The scye depth was determined as C/4–1.7 cm, and the front and back Interscye was set at (1/2 × actual measurements)–0.2 cm. The front-back neck breadth was set to (1/5 × base neck circumference)–1.3 cm and (1/5 × base neck circumference) cm. The front-back neck depth was set to (1/5 × base neck circumference)–1.2 cm and 3.5 cm. Front chest circumference was C/4–1 (front-back difference)cm; (1/4 × back chest circumference) was C/4 + 1 (front-back difference) + 0.3 (dart amount) cm. Front waist circumference was W/4–0.2 (front-back difference) + 2.2 (dart amount) cm; back waist circumference was W/4 + 0.2 (front-back difference) + 2.5 (dartamount) cm; front hip circumference was H/4 + 0.2 (ease) + 0.2 (front-back difference) cm; and back hip circumference was H/4 + 0.2 (ease)–0.2 (front-back difference) cm; Front droop was 1.6 cm. The newly developed tight-fit pattern is expected to be of great use as a basis for garment construction.

참고자료

· 없음