CFST의 D/t 제한모델들에 대한 신뢰성해석에서 모델링불확실성을 해결하는 선택적 방법
* 본 문서는 배포용으로 복사 및 편집이 불가합니다.
서지정보
ㆍ발행기관 : 한국전산구조공학회
ㆍ수록지정보 : 한국전산구조공학회 논문집 / 28권 / 4호
ㆍ저자명 : 한택희, 김정중
ㆍ저자명 : 한택희, 김정중
한국어 초록
콘크리트충전강관(Concrete Filled Steel Tube, CFST) 기둥 설계 시, 강관의 국부좌굴을 방지하기 위하여 강관두께 t에 대한 기둥외경 D의 크기를 제한하고 있다. 각각의 설계시방서에서 각기 다른 최대 D/t 값을 제안하고 있으며, 강재의 항복응력 fy, 또는 fy와 강재의 탄성계수 E의 식으로 표현된다. fy와 E의 불확실성을 고려할 경우, 최대 D/t 계산식을 포함한 한계 상태함수(limit state function)를 구성하여 CFST 단면의 국부좌굴에 대한 신뢰성지수(reliability index) β를 산정할 수 있다. 결정된 β는 사용된 최대 D/t 계산식에 따라 달라질 것이다. 이러한 신뢰성해석(reliability analysis) 결과의 가변성(variability)은 한계상태함수에 포함되는 전산모델 선택의 모호함(ambiguity)에서 기인한 것으로 모델링불확실성(modelling uncertainty)이라 한다. 모델링불확실성은 정보적불확실성(epistemic uncertainty)의 하나로 알려진 불명확성(non-specificity)으로 고려할 수 있으며, 불명확성은 가능성분포함수(possibility distribution function)를 사용하여 모델링할 수 있다. 본 연구에서는 다른 3개의 최대 D/t 계산식을 사용하여 주어진 CFST 단면의 국부좌굴에 대한 신뢰성해석을 수행하고 각각의 신뢰성지수를 계산할 것이다. 불명확한 신뢰성지수들은 가능성분포함수를 사용하여 모델링되고, 이로부터 확신정도(degree of confirmation)를 측정할 것이다. 확신정도는 신뢰성지수가 감소하면 증가한다. 결과적으로, 확신정도에 따라 재구성된 신뢰성지수들을 얻을 수 있으며, 허용 확신정도와 함께 CFST 단면의 국부좌굴에 대한 신뢰성지수의 결정이 가능하게 된다.영어 초록
For the design of Concrete-Filled Steel Tube(CFST) columns, the outside diameter D to the steel tube thickness t ratio(D/t ratio) is limited to prevent the local buckling of steel tubes. Each design code proposes the respective model to compute the maximum D/t ratio using the yield strength of steel fy or fy and the elastic modulus of steel E. Considering the uncertainty in fy and E, the reliability index β for the local buckling of a CFST section can be calculated by formulating the limit state function including the maximum D/t models. The resulted β depends on the maximum D/t model used for the reliability analysis. This variability in reliability analysis is due to ambiguity in choosing computational models and it is called as “modelling uncertainty.” This uncertainty can be considered as “non-specificity” of an epistemic uncertainty and modelled by constructing possibility distribution functions. In this study, three different computation models for the maximum D/t ratio are used to conduct reliability analyses for the local buckling of a CFST section and the reliability index β will be computed respectively. The “non-specific βs” will be modelled by possibility distribution function and a metric, degree of confirmation, is measured from the possibility distribution function. It is shown that the degree of confirmation increases when β decreases. Conclusively, a new set of reliability indices associated with a degree of confirmation is determined and it is allowed to decide reliability index for the local buckling of a CFST section with an acceptable confirmation level.참고 자료
없음태그
"한국전산구조공학회 논문집"의 다른 논문
- 페리다이나믹스를 이용한 균열진전 문제의 구조 최적설계7페이지
- 승강기 와이어로프 진단을 위한 누설자속기법 기반 국부손상 진단7페이지
- 전역적/국부 응답을 이용한 철골조의 모델 업데이팅 기법 제안8페이지
- 모듈 조합조건을 고려한 모듈러 강교량 상부구조의 정보모델 생성8페이지
- Precast Concrete Block 및 Suction pile을 적용한 Jacket 구조물의 ..10페이지
- 도시정보모델의 침수피해정보관리에서의 활용8페이지
- 마찰 진자 원리를 적용한 기계식 댐퍼의 개발에 관한 연구8페이지
- EM센서를 활용한 PSC 텐던 긴장력 손실 관리6페이지
- 지반과 말뚝의 상호작용을 고려한 고정식 해상풍력터빈의 동적 특성에 대한 확률적 평가8페이지
- 철골모멘트 골조의 붕괴성능에 영향을 미치는 불확실성 분석9페이지