전자전기컴퓨터설계실험3 - 예비레포트 - 실험02_ RC Circuit (A+)
- 최초 등록일
- 2020.11.26
- 최종 저작일
- 2020.06
- 15페이지/ MS 워드
- 가격 2,000원
소개글
"전자전기컴퓨터설계실험3 - 예비레포트 - 실험02_ RC Circuit (A+)"에 대한 내용입니다.
목차
1. Introduction (실험에 대한 소개)
가. Purpose of this Lab
나. Essential Backgrounds (Required theory) for this Lab
2. Materials & Methods (실험 장비 및 재료와 실험 방법)
가. Experimental data to obtain and Order of experiment
나. Materials (Equipment, Devices) of this Lab
3. Supposed Data and Results of this Lab (예상 실험 결과)
가. Pre-Lab 1.
나. Pre-Lab 2.
다. Pre-Lab 3.
4. Matters that require attentions (주의 사항)
가. Attentions to manipulate equipment
나. Cause of suppose error & Effort for reducing error
본문내용
1. Introduction (실험에 대한 소개)
가. Purpose of this Lab
Transient Response, Frequency Response, 전달함수를 이해하고, 원하는 대역폭을 갖는 RC회로를 구현할 수 있다.
나. Essential Backgrounds (Required theory) for this Lab
(1) RC Circuit - Transient Response
(가) Differential equation in RC Circuit
R과 C의 노드에 KCL을 적용시키면
(v_c (t) - V_s)/R+C (v_c (t))/dt=0
로 표현할 수 있다.
이를 Differential equation을 통해 풀면
v_c (t)=V_S - V_S 〖 e〗^(-t/RC)
임을 알 수 있다.
(나) Time Constant (τ) in RC Circuit
Time Constant는 System에서 63.2%(1-1/e)만큼 감소하는데 걸리는 시간을 말한다.
< 중 략 >
(3) PSpice 사용법
(가) 회로 구현과 ‘Simulate’ 사용법
PSpice에서 ‘Ctrl + G’를 눌러 화면에 소자를 생성한 후 ‘Ctrl + R’을 눌러 원하는 방향으로 회전시킬 수 있다. 그 다음 각 소자를 연결시켜 그림 1과 같이 회로를 구성한다.
원하는 부분의 V_OUT을 구하려면 ‘Voltage/Level Marker’를 눌러 그림 2와 같이 node에 연결시킨다.
그 다음으로 ‘Setup Analysis”를 눌러 원하는 부분에 맞게 설정을 한 다음 ‘Simulate’를 눌러 결과를 확인한다.
2. Materials & Methods (실험 장비 및 재료와 실험 방법)
가. Experimental data to obtain and Order of experiment
(1) Procedure of the Lab 1.
(가) 주어진 회로와 구하고자 하는 데이터
참고 자료
Irwin, 『Engineering Circuit Analysis 11th』, WILEY(2015), p270-p274, p511-522
“정보통신기술용어해설" http://www.ktword.co.kr/index.php
실험 교안 pdf파일