METHODS: The properties of the asphalt concrete were evaluated for different mineral filler types and ... CONCLUSIONS : TDF ash can be effectively recycled by being used as a mineral filler in asphalt, as it ... this study was to evaluate the properties of an asphalt concrete mix that used TDF ash as the mineral filler
The effects of fillers on the mechanical and thermal properties of glass/novolac composites have been ... Three different fillers, such as calcium carbonate, aluminum oxide, and wood powder were used for glass ... Therefore, it is very important to set up the combination of fillers for GFRP manufacturing to improve
amount of the filler used. ... The particle size of the pigment is extremely finer than that of the filler and should be reduced the ... The extra inclusion of the pigment in the mixture increased the amount of the filler and affected on
In this study, the properties of organic-inorganic hybrid insulating materials using inorganic fillers ... After evaluation with different inorganic fillers, Mg(OH)2 showed the highest thermal conductivity; on
study focuses on finding out engineering characteristics of asphalt concrete mixtures using mineral fillers ... this study were made with 25%, 50%, 75% and 100% of mixing ratio based on the conventional mineral filler ... The results indicate that the application of recycled waste lime as mineral filler improves the permanent
The purpose of this study is to research into which characteristic is shown according to a change in filler ... major characteristics of this study were experimented by having Bevel angle as 50°, Root gap as 3mm, Filler
of melting point and wettability with addition of Sn into Al-20Cu-10Si filler metal. ... For the development of a low-melting point filler metal for brazing aluminum alloy, we analyzed change ... DSC results showed that the addition of 5 wt% Sn into the Al-20Cu-10Si filler metal caused its liquidus
Resin filler also could be checked by OCT. ... However, no imaging method is adopted for resin filler distribution. ... To improve the physical properties of resin material, resin filler have to be added.
In improving adhesions between resin and fillers, the surface of the carbon filler materials were chemically ... , possibly from enhancement in wetting property of the surface of the filler materials. ... Crystallization temperature and rate of crystallization increased with increases in filler concentration
The porosity is varied as 0.2, 0.5, and 0.8 to account for the effect of filler granule geometry. ... The porosity and heat transfer coefficient of filler material as well as inlet velocity of heat transfer ... the heat transfer coefficient is adopted to assess the heat transfer between heat transfer fluid and filler
The electrical conductivities also increased with increasing content of nanotube filler. ... The specimen having a nanotube filler content of 0.6 wt% showed higher thermal conductivity than that ... As the concentrations of nanotubes filler were increased in the composite specimens, their storage and
The measurement finds that as the filler particle ratio increases, the tap density value continuously ... The filler particle ratio is adjusted up to 5~31% to produce a mixed particle, and then the tap density ... used for the investigation features a 12~22 μm- and 8~16 μm-sized main particles, and 1~2 μm-sized filler
The relative viscosity was measured at different filler loadings for a cycloaliphatic epoxy resin and ... For all the silica loadings used, ln (relative viscosity) varied linearly with filler loadings. ... Various empirical models were fitted to the experimental data and a fitting parameter such as critical filler
, it deems that the melted
slag mixed 1:1 with mineral filler could be used for sub-based. ... moisture content, sand equivalent, particle size distribution)
of melted slag mixed 1:1 with mineral filler ... Considering also the max dry density and
modified C.B.R value according to the replacement rate of mineral filler
develop composite fillers containing dielectric materials. ... Recently, methods that usea carbon-based filler, a conductive nanomaterial, have been investigated to ... In this study, we added geometric changes to a carbon fiber, a typical carbon-based filler material,
This study investigates the effect of filler content (wt%), presence of interphase and agglomerates ... The Halpin-Tsai micromechanical model is modified to account for the effect of interphase and filler ... The presented results highlight the need of considering various experimentally observed filler characteristics
tribological properties of acrylonitrile-butadiene rubber (NBR) filled with two kinds of carbon black filler ... Different types of Semi-Reinforcing Furnace (SRF), and High Abrasion Furnace (HAF) blacks were used as filler ... Mechanisms for the friction and wear behavior of NBR with different sizes of carbon black filler were