Shrinkage of RCC is measured according to KS F 2424. ... CONCLUSIONS: According tothe results of numerical analyses using various design inputs, composite pavements ... strain from the bottom of the asphalt layer tothe bottom of the rigid base layer, which can prevent
Recently the REPF is being upgraded tothe REPF+, a scaled-up facility. ... The PYMUS is currently being upgraded to include a Near-Real-Time Accountancy (NRTA) statistical analysis ... Assay (NDA) equipment for input-material accountancy, and a Hybrid Induced-fission-based Pu-Accounting
The purpose of this research is to analyze the performance of national R&D projects and to find out measures ... Third, it is necessary to improve information input and accumulation system along with improvement of ... The performance indicators of the energy HRD projects are related tothe research capacity, the number
In addition, we measured the available physical and chemical parameters controlling the distribution ... Therefore, the water temperature and freshwater inputs in the Jinju Bay were important environmental ... In order to provide important information for the efficient management of the identified farm ecosystem
configuration, and the 4 electrical inputs were supplied tothe beamformer. ... A series of impedance measurements were conducted to check the uniformity of the individual quadrants ... was measured and analyzed.
were respectively measured, proving the potential of MXene for a promising material in the desalination ... Research is going on to improve the electrode materials to improve the efficiency of the process. ... technologies, such as different types of distillations and reverse osmosis processes, need higher energy input
stake in Yogiyo, and took measures to prevent the sharing of Yogiyo’s data until the sale was completed ... In today’s transition tothe digital economy, data is being evaluated as a key input factor that determines ... , to allay concerns about restrictions in the competition due to data concentration.
Muntinga, Moorman, & Smit, 2011), contribution refers to consumers’ inputs to content created by brands ... The results of confirmatory factor analysis (CFA) showed that themeasurement model achieved acceptable ... In addition, the participants were asked to answer questions pertaining totheir perceptions of visual
|_/|_inputtothe its output integral dv.dt value that was measured by using experimental equipment ( ... value of input square wave _|-|_|-|_ tothe its output integral dv.dt value that was measured by using ... Set theinput wave frequencies of various 10 KHz, 50 KHz, 100 KZ, 200 KHz, 400 kHz and compare themeasured
To measure the input resistance, measurethe DC current flowing intotheinput side, changing the DC ... Tomeasurethe output resistance, apply 0 V totheinput and measurethe DC current flowing intothe ... and phase, and record in the report. (5) Directly measuretheinput resistance and the output resistance
Slew rate =2 π f VWhere slew rate is measured in {V} over {T} although actual measurements are often ... Op-amps sense the difference between the voltage signals applied totheir two input terminals and then ... Experimental process Measure basic characteristic of Operational amplifier (1) Find the common mode voltage
The company has implemented many measures to increase its economic, social, and environmental sustainability ... input-time, and longer-lasting overall final product, as compared to typical fast fashion items. ... the farm tothe final product.
The ‘jumps’ in the output square wave is making it very tricky tomeasurethe real V_{ o,pp}. ... G During the experiment, we could see that as theinput frequency went up, V_{o, pp} measured became ... However, this is due tothe circuits inside the op amp to reduce the effect of the frequencies.
(The control knob should be close to its full ccw position.) b) Measure and record the three stator winding ... for minimum resistance(control knob turned fully clockwise cw). d) Measurethe three stator winding ... Because thetorque is 9lbf.in, the line current is 2.2A and theinput voltage is 120Vdc so, input power
Source follower had a gain of about one, indicating that the output signal appeared similar totheinput ... data to check input-output transfer characteristics of circuit 1input voltage(V)(V)Operation area input ... value of the source follower amplifier is close to 1. -> The voltage at the source can be output to
theinput voltage to identify the DC characteristics. ... However, due tothe narrow bandwidth, there can be a problem when a high input frequency signal is received ... data to check input-output transfer characteristics of circuit 1Input voltage ( V _{GG}) Output voltage
We used ultrasonic sensors tomeasuretow cases. ... We can compare the results to be different when theinput type is different. ... When the sensor detected vehicle in front of our vehicle, figure step 1, sensor measurethe distance
Consider the means you will use to bridge the capability gap. 5. ... Define what theTo-Be process should or should not do when it’s completed(the goal of the project) 4. ... Determine what the As-Is process is or isn’t doing now (concrete measures) 3.
is actually used by dividing 20 intotheinput 1 voltage. ... Thermocouples measured the temperature difference by exposing different metals to different temperatures ... Resistance thermometer detectors measured the temperature by measuring the resistance, using the principle
The PID controller is used to calculate the error value as a collision between themeasured process variable ... linearly respond tothe change of theinput position value. ... It was also applied to modify the process control inputs to minimize errors.