바인더 강성이 아스팔트 콘크리트의 인장강도와 소성변형 특성에 미치는 영향 분석
* 본 문서는 배포용으로 복사 및 편집이 불가합니다.
서지정보
ㆍ발행기관 : 한국도로학회
ㆍ수록지정보 : 한국도로학회논문집 / 12권 / 2호
ㆍ저자명 : 김현환, 유민용, 김진철, 김광우
ㆍ저자명 : 김현환, 유민용, 김진철, 김광우
한국어 초록
상대적으로 강성이 큰 바인더가 높은 소성변형 저항력과 인장강도를 보이므로 바인더 강성이 아스팔트 혼합물의 러팅과 인장강도에 대해 중요한 인자라 할 수 있다. 혼합물의 인장 특성은 25℃에서 간접인장강도(ITS) 시험으로, 그리고 소성변형 저항성은 가장 보편적으로 60℃에서 반복주행(WT) 시험에 의해 측정된다. 변형강도(SD)는 60℃에서 아스팔트 콘크리트의 소성변형 저항성 추정을 위해 새롭게 개발된 특성이다. ITS와 SD는 정적재하 시험에 의해 측정되어 매우 간단하지만, WT는 상대적으로 긴 시간과 노력을 필요로 하는 반복 하중에 의해 얻어진다. 이 3가지 특성은 모두 바인더 강성에 의존하기 때문에, 한가지로부터 다른 하나의 특성을 추정하는 것이 가능할 것이다. 본 연구는 ITS 또는 SD시험에 의한 WT 소성변형 특성, 그리고 SD에 의한 ITS 추정의 가능성을 조사하였다. ITS에 의한 WT 추정결과 R2≒0.6으로 ITS가 높으면 WT 침하깊이가 낮은 경향을 보이는 것으로 관찰됐다. SD에 의한 ITS 추정은 R2≒0.64를, SD에 의한 WT 추정은 R2≒0.84를 보여 3가지 중에서 가장 높은 상관관계를 나타내었다. 결론적으로 SD에 의한 소성변형 저항성 추정 가능성이 상대적으로 높으며, 비록 R2이 다소 낮기는 하지만 WT와 ITS 결과 간에도 어느 정도의 상관성이 있다.영어 초록
Since the relatively stiff binder shows a higher tensile strength as well as higher rutting resistance, it is believed that the binder stiffness is an important factor for rutting and tensile strength of asphalt mixtures. The typical tensile property is measured by indirect tensile strength (ITS) test at 25℃ and the rutting resistance is most widely measured by wheel tracking (WT) test at 60℃. The deformation strength (SD) is newly developed property to estimate rut resistance of asphalt concretes at 60℃. The ITS and SD are very simple to measure by static test techniques, but the WT is measured by repeated loading procedure which requires relatively longer time and more efforts. Since these three properties are highly dependent upon the binder stiffness, it may be possible to estimate one property from another. Therefore, this study investigate the possibility of estimating the rutting characteristics (measured by WT test) by ITS or SD test, and the ITS by SD. Because of binder stiffness effect, in the WT estimation by ITS, a tendency was observed for the higher ITS mixture to have the lower rut depth, giving R2≒0.6, on the average. The ITS estimation by SD showed R2≒0.64, and the WT estimation by SD showed R2≒0.84, which is highest correlation among the three. Therefore, it was concluded that there is relatively good possibility of estimating WT result by SD, and even though R2 is somewhat low, there is some correlation between WT and ITS.참고 자료
없음태그
"한국도로학회논문집"의 다른 논문
- ZAM 모형을 이용한 청주시 간선가로 구간의 사고모형 개발7페이지
- 실내동결시스템을 이용한 노상토의 동상 특성9페이지
- 입도조정기층 재료의 공학적 특성 평가 및 경험적 상관모형 개발7페이지
- 콘크리트의 동결융해 내구성에 공기량, 제설제, 노출조건이 미치는 영향에 관한 연구7페이지
- 용도 및 규모특성을 고려한 산업단지 공장시설의 부설주차장 설치기준 개선방안 연구8페이지
- 최소단면 보수지역의 평탄성 평가5페이지
- 포스트텐션 콘크리트 포장의 Gap Slab 설계 방안10페이지
- Falling Weight Deflectormeter를 이용한 동상방지층의 구조적 특성 분석8페이지
- 오르막차로 통행방법 개선에 따른 효과분석7페이지
- 배수성 포장용 고점도 개질 아스팔트 바인더 개발10페이지