심야보일러 대체용 Cascade Cycle 히트펌프 적용에 따른 성능 평가
* 본 문서는 배포용으로 복사 및 편집이 불가합니다.
서지정보
ㆍ발행기관 : 한국기계기술학회
ㆍ수록지정보 : 한국기계기술학회지 / 12권 / 3호
ㆍ저자명 : 정훈, 황성욱
ㆍ저자명 : 정훈, 황성욱
목차
Abstract1. 서론
2. 심야전력 현황
2.1 심야전력제도 도입 배경
2.2 심야전력제도 운영 및 보급 현황
3. 히트펌프 구성
3.1 심야보일러 대체용 히트펌프의 특징
3.2 Cascade Cycle 히트펌프 구성
3.3 실외기 Cycle 구성
3.4 실내기 Cycle 구성
4. 최적 Cycle 구성을 위한 시뮬레이션
4.1 다단압축 Cycle의 압축비 최적화 모델
4.2 열부하 추종 운전 적용 모델
4.3 실외 온도별 난방 성능 시뮬레이션
4.4 실외 온도별 난방 성능 시험 결과
5. 결론
5.1 심야보일러 대체용 히트펌프 CycIe
5.2 표준 급탕 조건에서의 적용 타당성
5.3 고온 출수 조건에서의 적용 타당성
5.4 향후 연구 내용
참고문헌
영어 초록
The cost to electricity is cheaper at night due to electric supply and demand policy in Korea. During daytime the loads are higher and extra generators are brought "on-line" to meet the demand. In the middle of night loads are lower and they need to throttle back the generators. So KEPCO (Korea Electric Power Corporation) offers "time of use" (TOU) rates to balance the grid load. The night storage heaters are generally on a separate circuit which is only switched on when the night rate is activated. Since 2000 the price of NG, kerosene and other petroleum based fuel for heating has been increased rapidly and overtook the price of electricity at last, so more and more people have chosen night storage heaters to save energy price. Currently about 900,000 customers are using electric night heaters and this causes shift of peak demand time to night in winter and increase of deficit spending. To solve this problem, replacing electric night heater by air-source heat pump has been proposed. An air-source heat pump can provide efficient heating and cooling for building, especially in a warm climate. When properly installed, an air-source heat pump can deliver one-and-a-half to three times more heat energy to a building than the electrical energy it consumes. This is possible because a heat pump moves heat rather than converting it from a fuel, like in combustion heating systems.참고 자료
없음태그
"한국기계기술학회지"의 다른 논문
- 차량탑재 고소 작업용 리프트 개발6페이지
- 전동 파워 리프팅 휠체어의 설계 및 제작에 관한 연구7페이지
- 유체를 이용한 흡입형 매연여과장치의 실험적 연구7페이지
- 소형 무인 로봇 항공기의 설계 및 제작에 관한 연구7페이지
- 산업기계용 공펌프 개발5페이지
- 무단변속기 특성을 이용한 V-벨트형 2단변속기의 효율특성5페이지
- 다구찌 기법을 이용한 베벨기어 사출금형의 최적화6페이지
- 구조물 체결용 로크너트 개발에 관한 연구10페이지
- 미분무수 노즐형상에 따른 분무특성에 관한 연구7페이지
- DI 압축착화기관에서 함산소 첨가제와 EGR의 동시 적용에 따른 배출특성6페이지