Measurements were repeated five times on two separate days in five clinically normal Beagle dogs at seven ... Because of its relatively low variation on repeated measurement, TEWL might be the most useful way of ... Of the seven anatomic sites sampled, the left and right pinnae showed the lowest variation in repeated
Jackknife 추정치와 Kocurs 추정치를 단순한 모델링기법을 적용한 모델추정치와 비교하여서 다중응답의 문제(Repeated Measurement Problem)의 발생여부와 ... Jackknife 추정치와 Kocurs 추정치를 단순한 모델링기법을 적용한 모델추정치와 비교하여서 다중응답의 문제(Repeated Measurement Problem)의 발생여부와 ... SP 방법의 장점중 하나는 개인의 응답자로부터 다수의 응답(Repeated observations)을 받을 수 있는 점이다.
This repeated measurement problem have been generally either ignored in practice or confined to upward ... Simple estimation methods which ignore the repeated measurement problem are here called the “uncorrected ... This assumption is not strictly valid when several repeated choices are made by each respondent.
용어의 정의 3.1 MSA(Measurement System Analysis): 측정시스템분석 제품과 공정 특성에 대한 측정 Data값을 얻는데 사용된 측정장비, 측정자, 측정방법, ... 목적 통계적인 수법을 활용하여 계측시스템의 반복성(Repeatability)과 재현성(Reproducibility)을 관리하여 계측시스템의 정밀도와 정확도를 유지하고 측정능력을 향상시키는데 ... ) 제품을 측정한 결과와 규격을 비교하여 양품과 부적합품을 판정하는 것 3.4 편의(Bias) 참값과 측정값의 차이 3.5 측정 반복성(REPEATABILITY) 동일한 측정자가 반복
(β=IC/IB) d) Change another transistor and repeat the measurement in procedure b ~ c. e) Change RB = ... 570 kΩ and repeat the measurement in procedure b ~ d. f) Based on the experiment, explain what conditions ... (β=IC/IB) d) Change another transistor and repeat the measurement in procedure b ~ c e) Change R2 = 6.8
The density measurement of each sample is repeated three times, and the amount of solution required to ... If the three measurements do not match within 0.0001 g/ml, repeat the experiment until consistent results ... If consistent values are not obtained, repeat this process. ⑧ Repeat these steps for each of the solutions
If the value of 3 times measured is not match within 0.0001g/mL, repeat until consistent results are ... The density measurement of each sample is repeated 3 times, and the amount of solution required is 2mL ... Repeat these methods, to get 3rd sample's density value.
Repeat steps 1, 2. 5. ... Repeat step 2, 3. 5. Set the output of the signal generator to 6V. Repeat step 2, 3. 6. ... Repeat steps 2, and record the data in the Table 5.3.
Repeat step 1~3 of Procedure 3.2 3. ... Make R1B Short and repeat step 3 to calculate the output resistance value of Q2(w.r.t node B). (2) Cascode ... Then measure or calculate the current ii, io.
Repeat step 2. d)Draw the drain characteristic curves of 2N7000. ... Repeat step 2. d) Draw the drain characteristic curves with source degeneration. ... 실험목표 1) To determine experimentally the drain characteristics of a MOSFET 2) To measure the voltage gain
Repeat the measurement in procedure 3.1.2~3.1.5.Note: In this step, use two probes. ... Use "math" function to measure output waveform Vout.8. ... Observe and capture measured Vout and compare with theoretical value.6.
Measure the pressure which is dynamic pressure by using programming Repeat the measurement by changing ... And, Wind Tunnel with 10m/s through ① by pan which is in ③ Measure the values by using Laptop, ⑤ Repeat ... Repeat same steps from 2) to 6). In Wake experiment, Set the manometer, , at 15mm.
The density measurement of each sample is repeated three times, and the amount of solution required to ... If the values measured three times do not match within 0.0001g/ml, repeat the experiment until a consistent ... measure once is 2 ml. 1.
Repeat steps with other model cars. ... After I measured the time of the car, I rounded the second. ... there was no friction force between the cardboard and air therefore to get the stable result I have to repeat
once more. (5) Remove the measured sample and repeat for other chemicals. ... the platinum ring and the liquid surface breaks, and read the scale at the moment of breakage. (4) Repeat ... in the measurement.
While running “upper-side_IQ.gvi”, run “Rx.gvi” and measure the signal.1. lower-side_IQ.gvi 실행 결과, 캐리어 ... Repeat the analysis with “lower-side_IQ.gvi” and “double-side_IQ.gvi”“lower-side_IQ.gvi” 실행 후 “Rx.gvi
Repeat the measurement in procedure 2~4. 7. ... Increase DC voltage Vin from -2V to 2V with 0.5V scale, and measure DC voltage at Vout. ... 실험목표 - Experimentally measure the characteristics of junction diode and draw graphs. - Study about small
Record laboratory temperature and pressure, and repeat it 3 times. ... Read the measurement on the scale (height of water) in the burette. ... A nalysis C arbonate O f P urpose T o determine the types of carbonate in a sample by measuring the amount