아주대 초고주파공학 프로젝트3 ADS를 이용한 Equal Ripple LPF Design
- 최초 등록일
- 2014.10.05
- 최종 저작일
- 2010.10
- 12페이지/ 한컴오피스
- 가격 2,500원
소개글
아주대 초고주파공학 정경영교수님 A+받은 레포트입니다.
한번도 배포된적 없는 100% 창작 자료입니다.
총3번의 프로젝트중 3번째 레포트입니다.
코멘트 및 고찰 ADS 및 HFSS를 통한 상세 시뮬레이션 포함되있습니다.
많은 도움 되시길 바랍니다.
목차
(a) Using Richard’ transformations and Kuroda’ identities, design an equal-ripple LPF which meets the above specification. Show all work for full credit.
(b) Using ADS, plot the attenuation (in dB scale) from 0 to 3 GHz for your circuit with ideal transmission lines (“TLIN” “TLOC”). Also, include ADS schematic.
(c) Repeat (b) with microstrip lines (“MLIN” “MLOC” “MSTEP” “MTEE”). LinCal package in ADS can be used to calculate dimensions for microstrip lines. Use “Rogers Duroid 5880”& for the microstrip
(d) If your LPF implemented in microstrip line does not satisfy the design specifications, perform optimization to satisfy the design specifications.
본문내용
→ (a)번에서 구한 값에 따른 전송선을 ADS로 구현하는데 먼저 W, L값에 상관없이(W, L값을 이용할 필요없이) 또한 유전체에 상관없이(Msub 소자 필요없이) 원하는 값을 갖는 전송선로와 shunt로 연결된 전송선로 with O.C.을 design
→ 이상적인 소자 TLIN과 TLOC를 이용하였기 때문에 결과는 예상하였듯이 이상적인 Low pass Filter의 그래프가 나왔다. 1GHz에서 -3dB주파수가 1GHz로 1GHz이전의 신호는 대부분 전달되고 그보다 큰 주파수를 갖는
(c) (30 pts) Repeat (b) with microstrip lines (“"MLIN”", “"MLOC”",
“"MSTEP”",“"MTEE”"). LinCal package in ADS can be used to calculate dimensions for microstrip lines. Use “"Rogers Duroid 5880”" for the microstrip substrate with the following parameters:
- Dielectric constant (): 2.2
- Loss Tangent: 0.0009
- Thickness (d): 45 mils (=1.143 mm).
Note: the thickness of conductor = 20 um.
→ 실제 W, L값을 고려하여 그에 따른 Z값을 갖는 전송선로 구현을 위해 Msub소자에 주어진 유전체 Rogers Duroid 5880에 대한 정보를 넣고 MLIN와 MLOC 을 사용하여 ADS 회로를 design하였다. 하지만 위의 design 역시 실제 신호가 공간에서 전송되는 것을 반영하지는 못하고 W
→ Optimization 변수 설정으로 MLIN 라인의 폭이 아닌 길이 L을 선택하였다. 길이 차이에 의한 위상 차이가 주파수 shift를 일으켰다
→ 전송선로를 이용한 LPF 설계와의 비교를 위해 Lumped 소자를 이용
참고 자료
없음